![]() ![]() It does all its decoding using the sound card inside the computer, and it can interface with a radio using a COM port. Free version was made available with HRD 5.Ī digital mode decoding and terminal program that uses no terminal unit, terminal node controller, or multimode hardware. It is part of HRD package and support PSK, QPSK, Contestia, CW, DominoEx, Hell, MFSK, MT63, OLIVIA, RTTY, RTTYM, THROB and SSTV. The last version of PSK31 Deluxe was shipped with the HRD 4.0 SP4 kit and is no more availabe and supported.ĭigital Master 780 is a windows multi-mode program which uses Ham Radio Deluxe for radio control. It has been replaced by Digital Master 780 and is now a legacy product. PSK31 Deluxe is a PSK31 and PSK63 program for novices and power users. DigiPan is the result of a joint effort between myself and Nick Fedoseev, UT2UZ, the author of MIXW32, and is intended to make PSK31 operation easier and more enjoyable for everyone. Windows freeware multimode program by F6CTE it supports BPSK31 QPSK31 PSK63 PSK63F PSK10 PSKFEC31 PSKAM CW CCW THROB 4 bauds THROBX RTTY SITOR-AMTOR-NAVTEX FELD HELL PSK JT65 HELL HF FAX SSTV FILTERSĭigiPan provides a panoramic display of the frequency spectrum in the form of an active dial scale extending the full width of the computer screen. PSK31, RTTY, SSTV, MFSK, MT63 Olivia Hellschreiber SSTV and other modes, Log, DXCluster, telnet access, log backup, Rotor, CAT and whatever you dream in a single program ![]() ![]() Compatible with DXbase LOGic 7 RYLogit TRX-Manager YPLOG. Support radio control interface for several ICOM, TenTec, Kenwood, and Yaesu transceivers. Dl-fldigi An adapted version of fldigi for HAB tracking chase car apps. There is no SSTV in FLdigi so you will have to look at something like q-sstv but it hates my line input settings and refused to work on any /dev/dsp settings, so it be time for a compiling session in my dreams tonight.HamScope is a freeware windows multi-mode communications package for amateur radio that supports: PSK31 BPSK and QPSK RTTY ASCII MFSK16 PACKET CW. SDR-Control is a full featured App to operate your Icom Transceiver at home or. Set the PTT switch to VoX for easy use if you are in QSO mode or use the fixed PTT oprion to TX BUT be careful that you have no local voice coms else you will be booted of Hamsphere for 5 minutes as 10mhz does not take voice just data like I was by an over zealous admin who thought HELL as a digital mode, did not sound right.Īll modes work well, but forget CW in the short term as it seems a tad difficult to get the proper RX decoded in multi QSO's (just like normal) Power settings in most cases should not exceed 6ģ. Mic input setting to about "3" so the audio level does not exceed the normal voice levels (I use the Green settings on the S Meter and set it to peak at the end of the green bar)Ģ. You need to set the Hamsphere application (I use the Java based one in Linux) to the following ġ. How this is where it gets a bit difficult. But you will need volume "11" set on the Hamsphere App to RX any signal (the waterfall remain blue in most cases with yellow on RX signals - so lower levels than you may be used to but it does work) It pays to turn the local volume on the headset / speakers down so you do not go deaf on RX/TXģ. ![]() Set the sound card (Configure|Sound Card) input up to your "line" device input not your mic inputsĢ. I confirm all modes in Fldigi work 100% with Ubuntu and the Hamsphere Java App at least on my box here in Bangkok, but like most things it is not super easy to set up (or is it - you decide).ġ. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |